******* EN ************************************************************************************************************* --> Version 3.57 / June 5, 2023 - General: 1. added log lines for "Log Recording Events" function - FDM-S3: 1. changed S3 startup handling 2. improved downconverter management --> Version 3.56 / February 10, 2023 - !!! it is recommended to make a backup of the "Documents\ELAD\ FDM-SW2" folder before testing this version !!! - General: 1. added the possibility to disable all scheduled recordings without going to delete them, the option is available via check box in the Recording Scheduler window 2. corrected visualization of the RDS PI Code when it is equal to 0, now 0000 is displayed and no longer ---- 3. reduced the minimum size of the IF and AF windows 4. made some corrections on the AF window graphics 5. added the value of the band filter on the IF windows 6. removed the automatic change of the reference level value (+10dB) when an attenuation value is inserted 7. various optimizations and corrections on the management of xml files (settings) 8. the settings of Downconverter, Transverter, Special Modes (GenericIF, FT-991) and CAT functionality are now saved according to the serial number of the FDM device 9. changes have been made to the CAT functionality, the names of the three CAT modes have changed, only the operation of the second mode changes, here are some explanations: - mode "Standard LO": only RX1 is available, only Local Oscillator changes - mode "Standard RX": only RX1 is available, Local Oscillator and Tuning Freq can be changed (enable/disable Lock to CF) - mode "Virtual RXs": all receivers (RX1 to RX4) are available, use Lock to CF to switch between Local Oscillator and Tuning Freq a problem with setting the mode in "Virtual RXs" mode has been corrected, the receiver is now selected before changing its remote mode CWR mode management has been added 10. profile management: - a problem with the management of the "Load Last Profile at Startup" and "Save Last Status in Current Profile on Exit" settings has been corrected - slightly modified the graphics of the profile management window - fixed a problem in updating the name of the configuration (Device Configuration) chosen when changing profile 11. fixed problems in the Recording Scheduler window: - the contents of the Repeat and File Prefix columns are now remembered when adding a new row - the content of the last line added is now saved in order to propose it again as the first line when the scheduler is empty 12. moved the marker strings down to avoid overlapping the notch strings and the zoom arrow 13. added the management of the channelization at 8.33kHz between 117.975MHz and 137MHz, to be active the step must be 8.33kHz or 8.333kHz and SNAP must be active, the channelization values are: 0, 8.300, 16.700, 25,000, 33,300, 41,700, 50,000, 58,300, 66,700, 75,000, 83,300, 91,700 and 100,000 14. added default steps 8.333kHz, 20MHz, 50MHz and 100MHz - FDM-S3: 1. fixed the overlap of clock status and OmniRig button 2. the preamplifier status is now saved on xml file --> Version 3.55 / February 14, 2022 - General: 1. the equalizer of the AF window and the use of memories while playing a file are now unlocked also in OFFLINE mode 2. added the possibility to choose whether or not to apply the color of the selected receiver to the texts of the RDS window 3. added the possibility to choose whether or not to have the secondary windows of the program always on top (RDS, DRM, Memories, DxCluster, Profiles, Advanced Tuning, ...) --> Version 3.54 / January 24, 2022 - General: 1. fixed an issue in the keyboard shortcuts management that prevented to enter a value for the filter BW, the notch filters and the notch frequencies 2. fixed a problem that prevented notches from activating automatically when clicking on the spectrum or waterfall 3. fixed the fact that the markers were displayed even if they were not activated (using the keyboard shortcut Q for example) --> Version 3.53 / January 20, 2022 - General: 1. added the possibility to refresh the startup window that presents the list of FDMs with a right click or with the F5 key NB: remember you can launch SW2 on an FDM double-clicking on it or using the ENTER key 2. colors management: - added the possibility to set a color gradation for the spectrum background - added the possibility to save all color settings to XML files - revised the Color Settings window slightly to accommodate the new features - the RDS data (Program Identification Code and Program Service) are now in the color of the receiver - added sample XML files for color management in the folder "Documents\ELAD\FDM-SW2\ColorSettings\" - fixed some issues in the XML file saving management and in the restore default management - fixed issues in the color management of IF, AF and RDS windows 3. corrected inconsistencies problems at the graphic level of the IF and AF windows 4. added the possibility to change the width of the Advanced Tuning window, you can now choose whether display 9 or 12 digits 5. fixed inconsistencies issues at the graphic level in the management of the AF window equalizer NB: due to internal software limitations the equalizer could be disabled when the AF window is opened, just reactivate it by clicking on the appropriate button, for clarity the display of the EQ ON label has been added at the top right when the equalizer is active 6. contextual menus: - fixed some minor issues in the contextual menus management - added the "Close Menu" choice to the different context menus to simplify their closing - added the Frequencies History contextual menu accessible with a right click on the frequency at the top of the main window, it allows you to choose one of the 20 latest frequencies set, you can also use the keyboard shortcuts CTRL+Z and CTRL+Y to recall one of those frequencies 7. a frequency entered with the keyboard and validated with ENTER is now added to the list of the Frequencies History contextual menu (and so reachable by the keyboard shortcuts CTRL+Z and CTRL+Y) NB: remember that by typing the frequency with the keyboard: - the '+' key allows you to append "000" to the frequency value - the 'Backspace' key allows you to delete a digit 8. keyboard shortcuts management: - improved management of keyboard shortcuts, it was momentarily disabled when some parameters were changed using the mouse - added the following keyboard shortcuts regarding playing a wav file: - CTRL+B and CTRL+F to rewind and forward by 10% (of the duration of the file) the reading position of the file - CTRL+SHIFT+B and CTRL+SHIFT+F to send the file reading position to the beginning and to the end NB: you can use CTRL+SHIFT+F to jump to the next file - added the Q keyboard shortcut that allows you to scroll through the different choices available when clicking on the spectrum or waterfall, i.e. Set Tuning Frequency, Set Marker (1 and 2), Set Notch (1 and 2) 9. tooltips and quick-start guide: - for demonstration purposes, added the display of some tooltips when right clicking on the question mark at the top right of the main window - updated the quick-start guide (accessible by clicking on the question mark at the top right of the main window) - added other tooltips, they are displayed when you place the mouse cursor on a control (buttons, labels, ...) 10. enabled the possibility to select a memory even during the playback of a file NB: attention, it is not possible to tune outside the span displayed during a playback and it is not even possible to change the LO during a recording 11. added a message pane (to replace some MessageBox/Popup) that is displayed at the top left of the spectrum or waterfall to notify various information, it is possible to view the latest messages by pressing the TAB key - FDM-S3: 1. improved the internal management of the FDM-S3 in order to reduce the probability of program hangs, the firmware version therefore changes to 1.9 --> Version 3.52 / November 2, 2021 - General: 1. fixed some minor issues on the memory files management (MEM, EiBi, SWSkeds), it may be necessary to reset the "Show Labels on" setting (Main Window / IF Spectrum / Main + IF Spectrum) 2. fixed some graphic problems (overlapping of writings and/or buttons, flickering of writings, ...) 3. added the possibility to temporarily remove the mute during the mute/TX condition by clicking (with any mouse button) on the mute panel (SPEAKER OFF icon and MUTE written at the top left corner) 4. increased the display time of the tooltips 5. fixed an issue on the management of the position of the OminiRig window, it was no longer displayed if it was closed when it was minimized 6. improved low-level loading of compensation offsets, some warning messages may now appear in case of incorrect setting 7. continued work on improving the management of xml configuration files 8. DRM management: - added in the setting window (tab Other) the possibility to choose the program retrieval source (default URL, custom URL or INI file), the file structure is predefined and must be respected - made some minor corrections on the programming display window (DRM SChedule) 9. improved DxCluster management: - fixed issues related to frequency values higher than 2^32 - by manually editing the DxClusterList.txt file it is possible to add other servers - added the choice "2 hours" to the list of time out - graphically modified the "DX Cluster Interface" window for a better use of the functionality - modified the "Contacts" window: - updated the default values ??of the limits of the buttons (160m, 80m, ...), the buttons 60m and 2m have been added, it is always possible to change these limits by manually editing the FDMSW2DxBands.xml file - fixed the fact that the Time (UTC/Local) column was not hidden if requested in the setup window - fixed the fact that the maximum number of contacts was not updated if changed in the setting window - speeded up the refresh of the list - added in brackets after the hour the time elapsed since the contact recovery time - reversed the display order of the contacts, the most recent are now at the top - the clicked contact remains selected until it disappears from the list due to time out or maximum number reached, by clicking it you can deselect it to be able to scroll the list more easily - added a button to clear the list - made the same changes in the main window as in the "Contacts" window 10. added GHz management on Advanced Tuning window - FDM-S2: 1. added the DLL EXTIO v3.20 which solves signal level issues for the 768k configuration, the possibility of using the previous version (v3.14) has been left - FDM-S3: 1. added DLL S3 version 1.11 which fixes a problem on the use of the downconverter (DCM), it is necessary to have an updated downconverter to use this version, for backwards compatibility the previous version (v1.10.1) is also present --> Version 3.51 / August 2, 2021 - General: 1. corrected/extended the frequency management above 2.147GHz for the memories 2. fixed some graphic issues regarding memories management 3. the Memories List window is now resizable, if minimized just click on the MEM button to bring it back to front, remember that a right click on the MEM button allows you to add the current frequency to the memory files 4. corrected in various points the frequency management when it is higher than 2.147GHz (Downconverter Mode e Transverter Mode): marker management, TMate management, TMate2 display management and Advanced Tuning window 5. corrected some problems in the notch management and removed the maximum frequency limit 6. the Memory Editing window (accessible from the Settings window) is now resizable and the management of the frequency value has been extended above 2.147GHz 7. corrected an error that prevented the decimal part of the frequency from being entered when it was managed in kHz 8. fixed an error that prevented setting a memory from the Station Memory Panel of the channel 2 window - FDM-S2: 1. removed the blocking of the activation of the preselector bypass if a conversion mode is active (Downconverter, Transverter, Panadapter) --> Version 3.50 / July 16, 2021 - General: 1. fixed some inconsistencies in the graphics of the Settings window and the channel 2 window 2. speeded up the loading of the GUI when starting the software 3. improved the management of xml files to avoid program crashes or inability to change settings 4. updated the default list of available steps, it is now possible to change the value of the step with the mouse buttons by clicking on the step value, it is also possible to invert the functionality of the buttons on the Tuning tab of the Settings window 5. fixed CTRL+ALT+R functionality not resetting all windows 6. fixed error in frequency variation when SNAP was active, frequency could get stuck until the SNAP was removed or until the step value was increased 7. corrected error in the management of the Tuning Bars with the mouse, tuning was not always possible 8. corrected / extended the frequency management beyond 2GHz in the Tuning Frequency Related Settings table (Tuning Step tab of the Settings window) 9. fixed error in the management of the AGC threshold for channel 2, the value was not reloaded correctly 10.the keyboard shortcuts G (SNAP) and H (LOCK) have been added along with some tooltips 11.in the management of Omnirig an option has been added that allows you to use other RXs (receivers) as well at RX1, this option remains in beta for now and is not compatible with the split option 12.added the possibility to change the measurement unit of the level from dBm to dBuV by clicking on the level value - FDM-S2: 1. the "Bypass Internal Preselectors" option present in the Advanced tab of the Settings window has been moved to the main window, this option is not saved as it is considered a test feature - FDM-S3: 1. fixed minor bug in the management of the attenuators 2. fixed error in the management of biases that were not always turned off 3. fixed some internal management that prevented the use of beta versions (black square model) of FDM-S3 on the latest versions of the FDM-SW2 software 4. added downconverter management (DCM): - when the option is enabled in the Advanced tab of the Settings window the downconverter is used to receive when the tuned frequency is higher than 108MHz - the word DCM to the right of the serial number on the main window lets you know if the downconverter is active or not - the downconverter must be associated with the FDM-S3 with the appropriate Search button on the Advanced tab of the Settings window - downconverter bias management is available in the Tuning Frequency Related Settings table (tab Tuning Step of the Settings window) - FDM-DUO: 1. corrected minor error in the management of the FDM-DUOr attenuators 2. an option has been added in the Advanced tab to be able to easily unlock the maximum frequency of use of the FDM-DUO and of the FDM-DUOr, so it is no longer necessary to manually modify the xml files --> Version 3.49 / March 9, 2021 - General: 1. fixed some inconsistencies and errors in the AF window graphics 2. added values on the AF window equalizer sliders and added the FLAT button - FDM-DUO: 1. added values on the equalizer sliders of the ADVANCED TX panel --> Version 3.48 / February 24, 2021 - General: 1. fixed the visualization of the active configuration and of the windows title, in some cases there were inconsistencies 2. solved the issue that reversed the position of the division between spectrum and waterfall on the main window 3. revised the "Layout" context menu of the main window 4. revised the context menus of the IF and AF windows 5. brought to 1 second the flashing speed of the ADC CLIP indicator --> Version 3.47 / December 23, 2020 - General: 1. new visualization of the list of FDM devices in the HW Setup window 2. various small graphic changes in the Settings window (accessible from the SET button) 3. improved management of controls when closing the Settings window 4. improved the handling of errors regarding the setting xml files 5. extended the frequency range up to 99.999.999.999Hz for TCP CF (Center Frequency) command and FX (Receivers Frequency) command - FDM-S3: 1. corrected visualization of attenuation values 2. added saving in xml files of the chosen attenuation value 3. changed the visualization of the active reference clock, the possibilities are: * Int : 10MHz internal (no reference input used) * Ext : 10MHz external (REF IN input used) * Gnss : GNSS system (GNSS ANT input used) * In Hold : waiting (no reference input used) NB: for "Ext" and "Gnss" the writings can be red (not in lock) or green (in lock) --> Version 3.046 / October 22, 2020 - General: 1. new DLL (ELAD_DspLib_v2_0_16_0_2) * issue fixed on Mono-WBFM demodulation at 384kSample/sec 2. WBFM demodulation now works at 384kSample/sec also when recorded files are played, if Device Configuration sample rate equals 192 kSample/sec, demodulation filter bands are auto-adjusted to 192kHz as max value also for playing recorded files --> Version 3.045 / October 15, 2020 - General: 1. new DLL (ELAD_DspLib_v2_0_16_0_1) * WBFM demodulation at 384kSample/sec for all FDM devices 2. changed WBFM demodulation which now works at 384kSample/sec, if Device Configuration sample rate equals 192 kSample/sec, demodulation filter bands are auto-adjusted to 192kHz as max value - FDM-S3: 1. new DLL (ExtIOmc_ELAD_FDMS3_v1_8_0_3) * minor fixes --> Version 3.043 / September 17, 2020 - FDM-S3: 1. new DLL (ExtIOmc_ELAD_FDMS3_v1_8_0_1) * added test feature --> Version 3.042 / September 11, 2020 - FDM-S3: 1. new (DLL ExtIOmc_ELAD_FDMS3_v1_7_0_2) * improved 24MHz configuration --> Version 3.041 / August 27, 2020 - FDM-S3: 1. new DLLs (ExtIOmc_ELAD_FDMS3_v1_6_0_1 and ELAD_DspLib_v2_0_13_0_1) * added management of bias 1 and bias 2, click on SET to open the Setup window, under the "Tuning Step" tab, use the "Tuning frequency related setting table" to set bias 1 and bias 2 --> Version 3.040 / August 7, 2020 - FDM-S3: 1. new DLL (ExtIOmc_ELAD_FDMS3_v1_5_0_1) * added management of new hardware configurations --> Version 3.039 / July 14, 2020 - FDM-S3: 1. new DLLs (ExtIOmc_ELAD_FDMS3_v1_4_0_1 and ELAD_basic_USB_FX3_v1_11_0_1) * fixed issue when loading 24MHz or 12MHz configurations from another configuration with different sample rate * old firmware version is now recognized at startup and updated to the latest firmware version --> Version 3.038 / July 8, 2020 - FDM-S3: 1. new DLLs (ELAD_DspLib_v2_0_12_0_2 and ExtIOmc_ELAD_FDMS3_v1_3_0_2) * added recording priority, to set recording priority click on SET, go to the "Recorder/Player" tab, select the "Recording Speed" value and then click Apply or OK (this setting is done only during recording, for standard acquisition mode or PLAY-FILE mode everything works as previous software versions) --> Version 3.037 / July 7, 2020 - General: 1. improved software stability 2. in addition to being used to drag the main window, the Signal Control Panel (where the s-meter is located) and the Receiver Commands Panel (where the name of the software and the version are located), give the possibility with a double click to switch between maximized and normal window states 3. fixed issue during files sequence playback, the name of the file did not change when the file number increased --> Version 3.036 / June 29, 2020 - FDM-S3: 1. added improvements in recording management 2. updated the dll (file ExtIOmc_ELAD_FDMS3_v1_2_0_1) --> Version 3.035 / May 29, 2020 - General: 1. fixed issue with shortcuts: CTRL+R (start recording) was executed when pressing CTRL+ALT+R (reset windows positions) - FDM-DUO: 1. corrected the position of some messages related to the transmission 2. added the possibility to right click on the ADV button to bring up the Advanced TX panel on top 3. fixed an issue on the tune functionality of the Advanced TX panel which caused the microphone PTT to be inhibited --> Version 3.034 / March 31, 2020 - FDM-S3: 1. added new frequency range management 2. added clock source management (INT. EXT. GPS) --> Version 3.033 / March 24, 2020 - General: 1. enlarged frequency viewing 2. added the possibility to press Enter to start the FDM-SW2 when the FDM devices selection window appears 3. added in the Graphics tab of the Setup window some options to: * highlight the selected receiver in the volumes panel: the volumes of the selected receiver are colored with the color of the receiver, it is possible to change the transparency of the color using the "Color Settings" window * color the step value with the color of the selected receiver * color the mode, the band filter and the AGC with the color of the selected receiver 4. changed the color management on the Advanced Tuning window: * if "Local Oscillator" (center frequency of the spectrum) is chosen, the color remains the default one * if you select "Selected Receiver" (selected receiver frequency) the color becomes that of the selected receiver 5. recorder/player: * modified the graphic part of the recorder/player especially for as regards the colors, the aim is to better highlight the different cases: turned off, recording scheduled, recording in progress and playing in progress * added the following keyboard shortcuts: - CTRL+L for LOOP PLAY - CTRL+R for RECORD - CTRL+P for PLAY and PAUSE - CTRL+S for STOP * fixed the window for entering the name of the recording so that it is easier to start recording * fixed the Recording Scheduler window and the Recording tab of the Setup window so that the controls are clearer 6. added support for CWR mode for Omnirig 7. fixed issue on the CAT 0xF7 TRANSCEIVER STATUS command (inverted again the status in the answer), added the possibility in the Setup window to invert the answer state of this command (this is for compatibility with some proprietary software) 8. fixed issue that set the focus incorrectly after having set the frequency with the keyboard (digits + entere key) - FDM-DUO: 1. fixed some minor errors in macro creation 2. fixed problem when closing the Stand-Alone panel 3. fixed the fact that after starting the software, and activating the transmission on a virtual receiver the input options for transmission were set to software defaults (KEY and MIC), now the software reads the value set on the FDM-DUO (the AUTO choice for the TX IN menu of the FDM-DUO, menu 32, is not yet supported) --> Version 3.032 / February 21, 2020 - OmniRig management: - corrected issue in reading the frequency - fixed some issues on rig2 management - optimized general management of OmniRig - removed LockToCF on RX1 and Lock ABS on RX2 - continued extension of the supported frequency range, including at graphic level for frequency display - added the possibility to delete a frequency digit with the backspace key of the keyboard typing a frequency - added shortcut to Lock ABS with the letter O on the keyboard - updated quick start window - modified the Advanced Tuning window, removed some features with malfunction - improved closing management of the software - updated the dll for the FDM-S3 (file ExtIOmc_ELAD_FDMS3_v0_22_0_2) - slightly revised the graphics of the setup window - TMate2 management: - corrected an issue in saving the settings - lowered the default value of the LCD refresh time (100ms) - added the possibility in the setup window to choose presets as regards the management of the main knob --> Version 3.031 / January 16, 2020 (alpha version) - extended to channel 2 the fix of startup crash due Hz/kHz setting --> Version 3.030 / November 28, 2019 (alpha version) - start of TMmini management - fixed startup crash due to Hz/kHz setting --> Version 3.029 / August 1, 2019 (alpha version) - updated the dll for the FDM-S3 (file ExtIOmc_ELAD_FDMS3 v0.21) - fixed an issue in the visualization of the current configuration near the serial number of the connected FDM device --> Version 3.028 / April 24, 2019 (alpha version) - started extension of the supported frequency range --> Version 3.027 / April 16, 2019 - updated the dll for the FDM-DUO (file ExtIOmc_ELAD_FDMDUO v1.21) --> Version 3.026 / April 2, 2019 - fixed CAT command 0xF7 TRANSCEIVER STATUS (inverted PTT state) - fixed CAT command 0x88 PTT OFF (answer inverted) - fixed anomalous behavior of the "FDM-DUO Advanced Tx" panel at reception of CAT commands 0x08 PTT ON and 0x88 PTT OFF - reviewed the graphics for the "Downconverter Mode" and "Transverter Mode" sections on the Advanced tab of the settings window - added the visualization of the current configuration near the serial number of the connected FDM device --> Version 3.025 / March 2019 - alpha version, not published --> Version 3.024 / February 2019 - fixed the graphic of the "FDM-DUO Advanced Tx" panel --> Version 3.023 / December 20, 2018 - fixed issue in the management of volume 2 (values 0.1 and 0.5 were not managed correctly and therefore it was not possible to use them) - revised the Dx Cluster Interface window - fixed issue in getting the frequency from CW Skimmer when the mode is CW and the auxiliary audio output mode is IF48kHz - revised the Station Memory tab of the Setup window - added the possibility to launch the SW2 by clicking on a choice of the list of FDM devices found --> Version 3.022 / December 14, 2018 - corrected problem (with the DUO) that set RX1 always in USB at startup - corrected some problems in synchronizing the mode between SW2 and DUO - corrected problems in the management of the Lock To CF and Lock Abs buttons - corrected some errors on the stand alone panel for the DUOr - improved part of the setup window graphics (alignment of the controls, added description label, reorganized the Audio card) --> Version 3.021 / December 7, 2018 - added keyboard shortcuts to select and deselect receivers (CTRL+1 to CTRL+4) - added keyboard shortcut for the "-> CF" function (J key) - added keyboard shortcut for the mute toggle of each receiver (CTRL+N) - modified the titles of the windows - corrected the problem that prevented to go down to 10Hz of filter in CW NR - added new help files - added two new values (10 and 20) to the "Volume 2 Gain Multiplier" menu in the Audio tab of the Setting Window - set the default of the display mode of the memories to "if in frequency range" - revised some graphic parts in the Setup Window and in the FDM-DUO Stand- Alone Panel --> Version 3.020 / July 3, 2018 - activated the new panel "FDM-DUO Tx Control", selectable from "Setup -> Advanced -> Use FDM-DUO TX Control Panel" - added controls and pop-ups on the "Rec" button --> Version 3.019 / June 19, 2018 - moved the reading of CW messages during the opening of the Adv Tx panel - added controls on "Lock to CF" checkbox --> Version 3.018 / June 15, 2018 - for the DUO: corrected a management problem of the CD (CW delay) CAT command - added on start up pop-up information about missing parameters on the xml files --> Version 3.017 / June 8, 2018 - corrected problem in the management of the Filter BW field of channel 2 - the visualization of the DUO panels is now aligned with the one of the AF and IF windows (Always on Top can be enabled or not, right click to call up the panel if it is not in the foreground) - for the DUO: corrected problem related to the right click on a receiver button, activation of TX mode with right click did not work well on all 2 channel receivers --> Version 3.016 / June 7, 2018 - added check box "DUO Windows always on Top" in the Graphics tab of the Setup window - corrected some problems of management and display of the notch filters - corrected problem in the management of volume 2 (AUX volume) of channel 2 --> Version 3.015 / May 23, 2018 - corrected some problems on the band filters management (notch filters "BW" and "Filter BW") --> Version 3.014 / May 18, 2018 - solved issues on xml files loading --> Version 3.013 / May 15, 2018 - added read of "Tx Comp Gain", "Tx Bandwith" and "MIC Gain" from FDMDUO --> Version 3.012 / April 30, 2018 - solved bug on VRX reinit on RX2 (audio and mode were not updated correctly) - added check "AF and IF Windows always on top" on the Graphics tab of the Settings window --> Version 3.011 / April 21, 2018 - solved bug on VRX reinit (audio and mode were not updated correctly) - added checks on cat commands decoding --> Version 3.010 / April 9, 2018 - added automatic switching of RX1 to Lock To CF when "Stand Alone = RX1" mode is activated from the "FDM-DUO Stand Alone Control" panel - corrected problem on "Reset Windows Position" functionality, it did not work if the main window was in Maximized Mode - added the initialisation of the transmission mode based on what was read by the FDM-DUO for all 4 receivers (previously it was only for RX1) --> Version 3.009 / April 6, 2018 - now AF and IF windows stay on top - updated the Windows Default Positions function, added missing panels (Ctrl + Alt + R) - added the "Reset Windows Positions" button in the Setup->Graphics tab (equals to Ctrl + Alt + R) --> Version 3.008 / April 5, 2018 - for FDMDUO: Lock to CF is now automatically activated for RX1 when "Stand Alone = RX1" is activated on the FDM-DUO Stand Alone Control panel - label improvements on FDM-DUO Stand Alone Control panel - IF windows positions are now saved correctly even if on another display --> Version 3.007 / March 4, 2018 - solved bug on FDMDS1Config file management - solved ECSS bug on the Setup->Tuning tab - corrected the dimension of the ch1 and ch2 tables on the Setup->Tuning tab - added info about callstack on MessageBox displayed --> Version 3.006 / March 30, 2018 - solved bug on station memory management when L.O Frequency mode is selected - added an option that allows to use the SW2 also when wrong SN is found (a xml file with the "_WrongSN_type" sufix is created in this case) - the help window is now not modal (not blocking) - solved bug presents when opening the ADVANCED TX panel when the demodulation is not started --> Version 3.005 / March 20, 2018 - fixed notch bugs; - resolved AGC bugs; - increased max audio devices to 200 --> Version 3.004 / March 19, 2018 - added valid serial number check - Setup - Advanced - Special Mode: change max freq to 165MHz - Verify Notch freq value saved at startup - Bug omnirig with CAT --> Version 3.003 / January 5, 2018 - Recording Timer Bug solved --> Version 3.002 / January 4, 2018 - solved TX button in advance setting - Recording TImer Bug solved - CAT Standard solved bug - SWBC import correct Data values automatically - solved Generic IF after exiting Transverter mode - Unload Station Memory file bug solved - on main form added the software version —-> Version 3.000 / December 27, 2017 - FDM-S3 support - Channel 2 support the CAT Slave mode (opt for two instances WSJT-X see APP NOTE n_6 - FDM-S1 now works, new library installed - Introduction the possibility to Lock that can lock only Local Oscillator instead of all - Max number of soundcards 30 - Profile setting improved - N1MM xml files support - Mouse wheel direction programmable - About display improved - RTTY setting to USB on DUO - Set Audio Volume 2 fractional value --> 1.171Beta 9 Nov 2017 interfaccia per gestione FDMS3, installazione nuovi driver --> 1.170Beta 20 Oct 2017 --> 1.168Beta 14 Sept 2017 --> 1.167Beta 01 Sept 2017 --> 1.166Beta 31 Aug 2017 --> 1.165Beta 21 June 2017 - bugs on Adv panel for FDM-DUO --> 1.164Beta 15 June 2017 - adden N1MM option on Advanced Setup panel --> 1.163Beta 07 June 2017 --> 1.162Beta 26 May 2017 - bugs on DLL load for FDM-S2 Y9 --> 1.161Beta 12 May 2017 --> 1.160Beta 28 April 2017 --> 1.159Beta 26 April 2017 --> 1.158Beta 31 March 2017 --> 1.157Beta 15 March 2017 - improvements Smeter for FDM-S1 --> 1.156Beta 25 February 2017 --> 1.154Beta 10 February 2017 --> 1.153Beta 10 February 2017 - Manage FDMS3 --> 1.152Beta 10 February 2017 - mode FT991/FT991A --> 1.151Beta 03 February 2017 - Added FT991 mode to PanAdapter panel (Advanced Setup) - Modified notch function - Added recognition FDM-s2\Y9 model --> 1.150Beta 28 December 2016 - Profile improvements - Web Soket: added on Setup form enable Server chekbox --> 1.149Beta 9 December 2016 - Added WEB soket: HTTP/TCP command Protocol v 0.11 --> 1.148Beta 21 October 2016 - OmniRig routine improvements (RX2 lock to VFOB) - Add Profile settings (on Graphic page setting): load Profile at starttup and save Profile before exit - Improvement save IF windows position - Profile improvements: save DUO adv settings - Settings improvements: setup, DUO adv, and DUO sync windows position --> 1.147Beta 13 October 2016 - introductionof Profiles to store and loadthe state of the software for easy recalling complex configurations (due to lot of configuration combination, the release is in Beta for a full debug) - Omnirig modification (still under construction) --> 1.146Beta 15 September 2016 - Add Peak Persistence option on Spectrum Trace and IF trace (settings on Graphics Setup) - Enable Peak Persistence make MAx Hold disabled. Enable Max Hold make Peak Persistence disabled. - Add check 'Enable waterfall average' for spectrum and IF trace - Disabled Max Hold for Waterfall trace - Improvement save settings for IF trace --> 1.145Beta 09 September 2016 - Improvement TCP command Set Demodulation (MD) --> 1.144Beta 22 August 2016 - Improvement Ch 2 Equalizer --> 1.143Beta 20 July 2016 - New TCP Protocol v 0.10 (see documentation) --> 1.142Beta 10 July 2016 Improve Equalizer --> 1.141Beta 06 July 2016 - New TCP Protocol v 0.08 (see documentation) --> 1.140Beta 01 July 2016 improve StartRecording for schedeuled recording (no log for library) --> 1.138Beta 22 June 2016 improve StartRecording for schedeuled recording --> 1.136Beta 01 June 2016 Re-enabled last demod frequency, last demod mode, last demod bandwidth in .wav file header (only test) improve StartRecording for schedeuled recording --> 1.135Beta 01 June 2016 Disabled last demod frequency, last demod mode, last demod bandwidth in .wav file header (only test) --> 1.132Beta 02 May 2016 improve REC status occourences (Bug?) New Tcp Protocol v 0.7 --> 1.131Beta 30 April 2016 Bug Transverter --> 1.130Beta 29 April 2016 - logging of scheduled recording events from .dll in file .txt under C:\Users\\Documents\ELAD\FDM-SW2\DspLib\ --> 1.129Beta 26 April 2016 --> 1.128Beta 18 April 2016 --> 1.126Beta 15 April 2016 - logging of scheduled recording events in file .txt under C:\Users\\Documents\ELAD\FDM-SW2\Recordings\ => this feature is enabled by default => to disable log files, un-check 'Log Rec Events' option in scheduled recording dialog - New TCP server (v0_06): control added to manage when client connections reach max --> 1.120Beta 24 February 2016 - bug fixed on .wav file enumeration for file number > 999 (library) - in "REC Options" dialog box, recording filename length limited to 64 chars - in "REC Options" dialog box, recording filename fields format are better explained - in "Recording Name" dialog box, recording filename length limited to 64 chars - new large cross pointer => right click on spectrum/waterfall -> "Mouse Cursor Type" -> "Large Cross" - vertical swap spectrum/waterfall => right click on spectrum/waterfall -> "Layout" -> "WaterFall + Spectrum" -> "Spectrum <> WaterFall" - option to set max number of wave file for single rec unlimited (library) => set with file number = 0 in "REC Options" dialog box - fixed bug on rec-scheduler when max number of file is reached (library) - fixed bug on rec-scheduler (library) --> 1.114Beta 30 December 2015 - DUO: bug fixed for audio file play in FDMDUO Advanced Tx panel 1) play standard and elad audio files: 48 kHz, 16 bit PCM mono/stereo --> 1.113Beta 18 December 2015 - New guard on REC scheduler for daily recordings with more than 24 hours --> 1.112Beta 18 December 2015 - fixed new auto-notch parameters for software - dynamic-reconfiguration for all auto-notch settings (library) - DUO: fixed bug on FDMDUO Advanced Tx panel when peripheral Audio Input or Output is missing - DUO: fixed bug on max frequency limit in HF at 54 MHz - DUO: in FDMDUO Advanced Tx panel 1) specified audio file play only for 48 kHz, 16 bit stereo wav files 2) loop option for played audio files - Adapted for DUOr - New TCP commands available: refer to FDM-SW2_TCPprotocol_v0.05 Document 1) modified LF command 2) new command to enable/disable SNAP and read SNAP status 3) new command to set frequency steps (use in SNAP mode) - auto-reading software installation version and display on startup panel - guard on open/close routines for recordings files (library) - fixed bug on pause/play routines for recorded files (library) - fixed bug on RTTY - fixed bug crash on management of reading Eibi file null --> 1.107Beta 26 September 2015 - label on Manual Notch filter even in REL(ative) mode show the Frequency no more Delta Frequency from Center - New TCP commands available: refer to FDM-SW2_TCPprotocol_v0.03 Document - Guard on REC scheduler for daily recordings with more than 24 hours - corrected bug on filename on recording (Bill) - corrected bug crash on setting Manual Notch filters --> 1.105Beta 12 September 2015 - improvement on Recording scheduler - introduction ABSolute and RELative mode on two Manual Notches (Absolute Mode works as previous version, changing tuning remain same (absolute value) frequency, RELative mode works in the fixed offset position related to Spectrum Center Frequency value.